Scytek electronic Remote Starter G40RS User Guide

GALAXY G40RS  
AUTOMATIC TRANSMISSION ONLY  
WITH SEPERATE LOCK/UNLOCK BUTTONS  
REMOTE START SYSTEM  
PRODUCT MANUAL  
 
Remote Transmitters  
Remote Transmitter Description  
LED  
Button 1  
Button 3  
Button 2  
Button 4  
The G40RS is a state-of-the-art remote starting system is supplied with two 4-button Remote  
Transmitters used to control system operations.  
The built-in remote start feature is designed to offer maximum convenience by remote starting your  
vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined time to  
provide a comfortable environment once you enter your vehicle.  
ScyTek Electronics Inc. and its VENDORS shall not be liable for any accident resulting from the use of this  
equipment. This system is designed to be professionally installed into a car or vehicle in which all items,  
such as parking brake and all associated components, Hood switches, transmission shift linkage, throttle  
linkage, and all engine safety features, are in perfect working condition.  
Do not ever Install G40RS in vehicles equipped with MANUAL TRANSMISSION.  
DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is  
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon. To  
ensure the safety and security of the system while it is remote started, the G40RS Starter employs several  
safeguards. In the event the brake pedal is pressed while the engine is remotely running, the remote  
start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle. The  
system is equipped with a hood pin input to prevent access to the engine compartment while the vehicle  
is remotely running. Finally, the Valet Mode prevents the remote start feature from operating in the event  
the vehicle is to be serviced.  
Button 1 Locks the doors and when held for 5 seconds, activates the system’s Car locator feature.  
Button 2 Unlocks the doors.  
Button 3 Feature programming only.  
Button 4 Activates and deactivates the Remote Start feature.  
Page 2 - G 40RS  
 
Adding/Replacing Transmitters  
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired  
transmitters ready and follow the steps below.  
Note: Up to four transmitters can be programmed to operate the system. To erase any previously stored  
transmitter codes, be sure to program all 4 transmitter memory locations.  
To program transmitter(s):  
1. Turn the ignition key On, Off, On, Off, and back On.  
· The parking lights will flash 3 times.  
2. Press and hold the Override switch for 5 seconds.  
· The parking lights will flash 5 times.  
· The LED will illuminate.  
3. Press Button 1 on the first transmitter.  
· The parking lights will flash once.  
4. Repeat steps 3 and for each transmitter (up to 4).  
5. Turn off the ignition key.  
· The parking lights will flash 3 times.  
G 40RS - Page 3  
 
System Operation  
Remote Locking  
To Lock the doors:  
1. Turn off the ignition.  
2. Press Button 1.  
· The doors will lock.  
· The parking lights will flash once.  
· The LED will turn on, to indicate the doors are locked.  
3. 10 seconds after Locking:  
· The LED will start blinking.  
Remote Unlocking  
To Unlock the doors:  
Press Button 2.  
· The doors will unlock.  
· The parking lights will flash twice.  
· The LED will turn off .  
Remote Starting Automatic Transmission Mode  
To Remote Start the System:  
1. Be sure the system is not in Valet Mode.  
2. Press and hold Button 4  
· The parking lights will flash twice.  
· The doors will lock (programmable)  
· The engine will start and run for the duration of its programmed Run Time.  
· The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).  
To resume control of the vehicle:  
1. Unlock the doors manually or with the Transmitter.  
2. Turn on the ignition.  
3. Press the Brake Pedal to disengage the remote start.  
Visual Car Locator Mode  
Use this feature to locate your vehicle in a crowded parking lot. Look for the flashing parking lights  
which should be your vehicle!  
To activate the Visual Car Locator Mode:  
1. Press and hold Button 1 for 3 seconds.  
· The parking lights will flash.  
· The doors will unlock allowing access to the vehicle.  
2. Press Button 2 to turn off Car Finder.  
Page 4 - G 40RS  
 
Valet Mode  
The Valet Mode temporarily disables the remote start system so the vehicle may be serviced by a mechanic.  
The remote transmitters will continue to lock/unlock the doors.  
To activate or deactivate the Valet Mode:  
1. Turn on the ignition.  
2. Press and hold the override switch for 5 seconds.  
· The parking lights will flash once and LED will be On to confirm the Valet Mode is on or twice  
and LED will turn off to confirm Valet Mode is off.  
3. Turn off the ignition.  
Shut Down  
When the the Remote Start feature is active, any of the following actions will shutdown the engine:  
1. Pressing Button 4  
· After the engine shuts down the doors will lock (programmable)  
2. Pressing the Brake Pedal.  
3. Opening the Hood.  
4. Remote Start Time-Out (completion of the timed run cycle).  
Quick Stop (Automatic Transmission Only)  
The Quick Stop Feature allows you to exit the vehicle while keeping the engine running for quick stops.  
To leave the vehicle running:  
1. Press Button 4 .  
2. The parking lights will turn on. Now turn the ignition key off and the vehicle will continue to run.  
3. You may now exit the vehicle and lock the doors manually or by using the Remote Transmitter.  
To resume control of the vehicle:  
1. Unlock the doors manually or with the Transmitter.  
2. Turn on the ignition.  
3. Press the Brake Pedal to disengage the remote start.  
Automatic Start Mode  
The Automatic Start Mode allows the vehicle to automatically start the vehicle every one or two hours and  
run for the preset Run Time. ( automatic start mode must be selected, feature # 8)  
To turn on Auto Starting:  
1. Turn Ignition switch Off and wait for 3 seconds.  
2. Turn Ignition switch On and Off three times ending with Ignition in Off position  
3. Press and release the Valet switch immediatly.  
Parking lights will flash indicating that the Auto Start mode has been activated.  
To turn off Auto Starting do one of the following:  
· Turn ignition On.  
· Arm and then Disarm the system  
· Alarm or Panic the system  
* Automatic Start Mode will stay active for 24 hours only.  
G 40RS - Page 5  
 
Ignition Door Locking  
For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems  
to automatically lock the doors when the ignition is turned on.  
Ignition Door Unlocking  
For added convenience, this feature automatically unlocks the doors after the ignition key is turned off.  
The Ignition Door Unlocking feature may also be completely disabled if desired.  
Battery Replacement  
Your Remote Transmitter uses (2) 3 volt batteries (type CR2016 ), which will require replacement  
in time. Depending on the amount of use, the battery may last up to six months or more before  
it needs replacement.  
When the battery needs replacing, the system’s operating range will decrease or the transmitter  
LED may not be as bright.  
In order to change the battery, separate the top and bottom halves of the case.  
While replacing the battery make sure that the positive and negative terminals are positioned  
correctly, then carefully reassemble the transmitter case.  
Entering System Programming  
To enter System Programming:  
1. Turn on ignition.  
2. Within 5 seconds, press the valet switch 5 times.  
· The parking lights will flash three (3) times indicating you have entered Programming.  
3. Press the valet switch the number times equal to the System Parameter you want to change.  
· The parking lights will flash each time the valet switch is pressed.  
4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for  
that System Parameter.  
· The parking lights will flash to indicate the setting.  
1 flash  
2 flashes  
3 flashes  
=
=
=
Button 1  
Button 2  
Button 3  
5. When you are finished, turn off the ignition to save the changes.  
Default Reset  
Following this procedure will set all System Programming Parameters to factory default settings.  
1. Enter System Programming.  
2. Press Transmitter Button 3.  
· The parking lights will flash 6 times indicating that the reset signal was received.  
· All System Programming parameters are now set to factory default settings.  
· The Valet Mode is off.  
Page 6 -G 40RS  
 
System Programming  
Branch Feature  
Button 1 (default)  
Enabled  
Enabled  
Single  
1 second  
On  
Button 2  
Disabled  
Disabled  
Double  
3 seconds  
Off  
Button 3  
1. Ignition Door Locking  
2. Ignition Door Unlocking  
3. Door Unlock Pulse  
4. Door Lock Pulse Length  
5. Lock after Start  
0.1 Sec  
6. Lock after Shutdown  
7. Engine Run Time  
8. Automatic Start Mode  
9. Tachless Sense Crank Time  
10. Engine Type  
On  
Off  
15 minutes  
Disabled  
Normal  
25 minutes  
2 hours  
Extended  
1 hour  
Super Extended  
Diesel Engine  
RPM Mode/RPM Learn Gas Engine  
11. Ignition 2 Output Program  
12. Unlock Before Start  
13. Horn Chirp  
Ignition 2 Output  
Disabled  
Enabled  
Accessory 2 Output Starter 2 Output  
Enabled  
Disabled  
14. Smart Start Run Monitor  
15. Trunk Release/ Horn Out  
Enabled  
Trunk Release  
Disabled  
Horn Output  
Jumper Selection  
Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking  
light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity  
output as described below, then reassemble the main unit case.  
Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay.  
Left Pin + Center Pin = positive  
Right Pin + Center Pin = negative  
default setting shown  
G 40RS - Page 7  
 
System Installation  
8-Pin Main Harness  
Pin 1 RED WIRE: Module Power Input (+). Connect to a constant source of +12V  
Pin 2 GREEN/WHITE WIRE: Brake Input (+). Connect to the wire that shows +12V when pressing the  
brake. The Green/white wire is a safety shutdown wire that must be connected.  
Pin 3 BROWN/WHITE: Horn Output (-) 500 mA. Connect to a relay to activate the vehicle’s horn when the  
alarm is triggered. This wire may instead be programmed as an ignition 3 relay trigger  
Pin 4 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows  
+12V or ground only when the parking lights are on and set the internal parking light relay jumper to  
the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with  
independent left and right parking light circuits, diodes must be installed to keep the circuits separate.  
NOTE: Do not connect the WHITE wire to the vehicle’s headlight circuit.  
Pin 5 WHITE/BLACK WIRE: Hood Pin Input (-). Connect the to the hood pin switch. The switch must  
provide a ground output when switch is opened.  
Pin 6 BLUE/ORANGE WIRE: Ground When Running Output (-) 500 mA. Connect to an optional factory  
security bypass module if required.  
Pin 7 BLACK WIRE: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away  
any paint or dirt to insure the best possible ground.  
Pin 8 BLACK/GRAY WIRE: Tach Input. Connect to the vehicle’s tach wire or a fuel injector wire if the  
tachless mode does not provide satisfactory operation.  
Page 8 - G 40RS  
 
2-Pin Blue Connector: Valet switch port. Mount switch where it is accessible from the driver’s position.  
2-Pin Red Connector: LED port. Mount LED where it may be easily seen from either side of the vehicle.  
3-Pin White Door Lock Connector: Door lock port.  
· BLUE WIRE - negative unlock output (-) 500mA.  
· RED WIRE - (+) 100mA trigger output for optional plug-in door lock relay module,  
· GREEN WIRE - negative lock output (-) 500mA.  
5-Pin White Flat Connector: Antenna connector port.  
Starter Diagnostics  
Starter doesn’t start and Parking Lights flash:  
3 Times - Hood Trigger is active  
4 Times - Brake Lights stay On  
5 Times - Unit is in Valet (service) mode, and start is disabled.  
G 40RS - Page 9  
 
Door Lock Diagrams  
Adding Actuators  
Negative Trigger  
Reverse Polarity  
Positive Trigger  
blue  
green  
Positive Horn Honk  
Page 10 - G 40RS  
 
Wiring Diagram  
Violet  
Yellow  
Orange  
Brown  
Red  
Starter Output  
Ignition 1 Output  
Accessory Output  
Ignition 2 Output/ACC/Starter2  
+12V Battery Input #1 25 Amp.  
+12V Battery Input #2 25 Amp.  
Red  
Red  
+12V Battery Input #3  
Green/White Brake Input(+)  
Brown/White Horn Output (-)500mA  
Control Unit  
G-40RS  
White  
Parking Light Output (+/- built-in relay)  
White/Black Hood/Trunk Input (-)  
Blue/Orange Remote Start output (-) When running  
Black  
Black/Gray  
Ground  
Tachometer Input  
For Factory Disarm pulse  
use the unlock wire  
Green Lock output (-) 500mA.  
Empty  
Blue  
Unlock output (-) 500mA.  
Enable unlock Before Start location  
# 12  
OVERIDE SW IN  
OUT  
LED  
Antenna  
System Programming: Added  
Button 1  
button 2  
15. Trunk Release/ Horn Out  
Trunk Release  
Horn Output  
ScyTek Electronics  
11627 Cantara Street  
North Hollywood, CA 91605  
© ScyTek Electronics 2009  
G 40RS 7-29-09  
 

RCA MP3 Player M1001GBUS User Guide
RCA Portable CD Player RP2810 User Guide
Roland Computer Monitor DS 30A User Guide
Rosewill Computer Hardware RC212 User Guide
Rotel Turntable RP 1000 User Guide
Samsung Digital Camera Digimax350 SE User Guide
Sanyo Battery Charger N 500AC User Guide
Sanyo Camcorder DSR C100 User Guide
Saturn Automobile 2008 Outlook User Guide
Sears Refrigerator 56489636 User Guide