Scytek electronic Automobile Alarm G 20 User Guide

VEHICLE SECURITY SYSTEM  
G-20  
 
Remote Transmitters  
Remote Transmitter Description  
LED  
Button 1  
Button 3  
Button 2  
Button 4  
The G-20 Security System is supplied with two 4-button Remote Transmitters used to control  
system operations.  
Button 1 Arms the system and when held for 2 seconds, activates the system’s Panic feature.  
Button 1 also locks the doors when the system is in Valet Mode.  
Button 2 Disarms the system. Button 2 also unlocks the doors when the system is in Valet Mode.  
Button 3 Activates the Auxiliary 1 output. This output will remain on for as long as the button is  
pressed.  
Button 4 Activates and deactivates the Anti Car-Jack feature if the option is enabled.  
Silent Operation:  
Button 4 then Button 1 Arms the system silently.  
Button 4 then Button 2 Disarms the system silently.  
Adding/Replacing Transmitters  
To replace lost or stolen transmitters or to add additional transmitters into the system, have all  
desired transmitters ready and follow the steps below.  
Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously  
stored transmitter codes, be sure to program all 4 transmitter memory locations.  
To program the transmitter(s):  
1. Turn on the ignition key On, Off, On, Off, and back On.  
· The siren will chirp 3 times.  
2. Press and hold the Override switch for 5 seconds.  
· The siren will chirp 5 times.  
· The LED will illuminate.  
3. Press Button 1 on the first transmitter.  
· The siren will chirp once.  
4. Repeat steps 3 for each transmitter (up to 4).  
5. Turn off the ignition key.  
Page 2 - G-20  
 
Tamper Alert  
If the system was triggered while away, the LED will flash to indicate which zone triggered the  
system after disarming and turning on the ignition. The LED indication will repeat 8 times.  
LED Flashes:  
1 flash  
=
=
=
=
=
=
optional sensor  
shock sensor  
not used  
door  
2 flashes  
3 flashes  
4 flashes  
5 flashes  
10 flashes  
trunk  
main power interrupt or system was reset  
example: flash-flash-pause-flash-flash-pause = shock sensor  
G-20 - Page 3  
 
System Operation  
Remote Arming  
The system monitors 3 independent areas (zones) while armed: doors, hood/trunk, and shock sensor input.  
To Arm the System:  
1. Turn off the ignition.  
2. Press Button 1.  
· The siren will chirp once.*  
· The doors will lock.  
· The parking lights will flash once.  
· The LED will turn On, to indicate the starter defeat is activated.  
3. 5 seconds after Arming:  
· The LED will start blinking to indicate that the doors and hood/trunk inputs are being monitored.  
* During Arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional times and  
ignore that input, but keep all other areas protected.  
Once Armed, the alarm will trigger when any of the following occurs:  
· The doors are opened.  
· The hood or trunk is opened.  
· The shock sensor detects an impact to the vehicle.  
When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will flash. If  
the system is triggered by the doors, or hood/trunk, the system will alarm for 45 seconds. If triggered  
by the shock sensor input, the system will alarm for 30 seconds.  
In the event the alarm is triggered and remains triggered continuously by the same sensor or input  
during a single arming cycle, that sensor or input will be automatically bypassed until the next time  
the system is armed.  
If the Shock Sensor detects a light impact to the vehicle, the siren will chirp 5 times as a warning  
indication.  
Remote Disarming  
To Disarm the System:  
Press Button 2.  
· The siren will chirp twice.*  
· The doors will unlock.  
· The parking lights will flash twice and will remain ON for 30 sec..  
· The dome light will turn on.**  
· The LED will turn off.  
* During Disarming, if the system was triggered while away from the vehicle, the siren will chirp 3 times, and the  
parking lights will flash 3 times.  
**If the optional Dome Light Activation Feature is installed  
Passive Arming  
When programmed for the optional Passive Arming feature, the system arms itself automatically, each time  
the ignition is turned off and all of the doors, hood, and trunk are closed.  
To start the Passive Arming Process:  
Page 4 - G-20  
 
1. Turn off the ignition.  
2. Open the door and exit the vehicle.  
· Once all doors are closed and the dome light is off, the LED will begin flashing rapidly.  
3. After 30 seconds,  
· The siren will chirp.  
· The parking lights will flash.  
· The doors will lock.*  
· The status LED will begin flashing.  
4. The system is now armed.  
* If the Passive Locking feature is selected.  
If the Passive Arming with Countdown feature is programmed, the siren will chirp every 2 seconds until the  
system passively arms.  
Note: If the Passive Arming feature is enabled, the Automatic Rearming feature will also be enabled even if it was not already  
programmed.  
Panic Mode  
In the event of an emergency, the transmitter’s Panic feature can be used to instantly trigger the alarm.  
To activate the Panic Mode:  
1. Press and hold Button 1 for 2 seconds.  
· The alarm will sound.  
· The parking lights will flash.  
· The doors will unlock* allowing access to the vehicle.  
2. Press Button 1 or 2 to stop Panic Mode.  
* If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.  
Emergency Override  
If the transmitter is lost or inoperable, the system can still be disarmed using the following procedure. Before  
beginning this procedure be sure to have the ignition key ready and know the location of the override switch.  
To Emergency Override the system:  
1. Unlock the door using the key.  
2. Enter the vehicle.  
· The system will trigger and the siren will sound.  
3. Turn the ignition key to the “On” position.  
4. Press and hold the override switch until the alarm shuts off.  
· The system will disarm.  
5. The vehicle will now be able to start.  
Optional Coded Emergency Override  
As an extra measure of security, the system is equipped with an optional Coded Emergency Override  
feature. Once an Emergency Override Code is chosen and programmed during installation, the system can  
no longer be disarmed using the standard override procedure.  
To Emergency Override the system using the Code:  
1. Follow steps 1-3 above.  
2. Press the override switch a number of times equal to the Disarm code, and continue holding for  
G-20 - Page 5  
 
10 seconds on the last press.  
· The system will disarm. If the code is entered incorrectly, turn off the ignition and begin again.  
To set the Emergency Override Code:  
1. Turn on ignition.  
2. Within 5 seconds, press the valet switch 5 times.  
· The siren will provide one long chirp, indicating that you have entered Programming.  
3. Press the valet switch 3 times.  
· The siren will chirp each time the valet switch is pressed.  
4. Within 5 seconds, press Button 3 on the transmitter.  
· The siren will chirp 3 times.  
5. Press the valet switch the number of times equal to the desired code (from 1-15).  
6. Turn off the ignition then arm the system.  
7. Disarm the system using the new Override Code to permanently store the new code.  
Note: If the code set procedure is not properly performed, turn off the ignition and begin again. The override code will not  
be permanently stored until the code is used to disarm the system.  
Valet Mode  
The Valet Mode temporarily disables the security system so the vehicle may be operated by a mechanic or  
parking attendant.  
To activate or deactivate the Valet Mode:  
1. Turn on the ignition.  
2. Press and hold the override switch for 5 seconds.  
· The siren will chirp once and the LED light will stay ON to confirm the Valet Mode is on.  
· The siren will chirp twice and the LED light will turn OFF to confirm the Valet Mode is off.  
3. Turn off the ignition.  
While in Valet Mode the remote transmitters will continue to lock and unlock the doors, and operate the  
optional auxiliary functions.  
Battery Replacement  
Your Remote Transmitter uses (2) 3 volt batteries (type CR2016 ), which will require replacement  
in time. Depending on the amount of use, the battery may last up to six months or more before  
it needs replacement.  
When the battery needs replacing, the system’s operating range will decrease or the transmitter  
LED may not be as bright.  
In order to change the battery, separate the top and bottom halves of the case.  
While replacing the battery make sure that the positive and negative terminals are positioned  
correctly, then carefully reassemble the transmitter case.  
Page 6 -G-20  
 
Extended Features  
Ignition Controlled Door Locks  
For added safety, the Ignition Door Locking feature allows vehicles equipped with power door  
lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors  
after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition  
locking feature is disabled to protect against locking the keys inside the vehicle.  
Dome Light Activation  
If the optional Dome Light Activation feature is installed, the dome light will turn on when the  
system is disarmed using the Remote Transmitter. The dome light will remain on for 30 seconds  
or until the ignition is turned on.  
Auxiliary Function Outputs  
The G-20 Security System is equipped with an Auxiliary Output allowing the convenience features  
of the system to be further expanded. This output can be used to add an optional feature such  
as: power trunk release, remote engine start, power window activation, power sunroof control,  
etc.  
Remote Shock Sensor Disable  
When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong  
weather conditions that could cause the Shock Sensor to trigger, the sensor can be temporarily  
bypassed using the Remote Transmitter, preventing possible false alarms.  
To disable the Shock Sensor :  
1. Arm the system normally.  
2. Within 5 seconds of Arming the system, press the Arm button again.  
· The siren will chirp 5 times and the parking lights will flash 5 times to indicate the sensor is disabled.  
· The sensor will remain disabled until the next arming cycle.  
Silent Arming/Disarming  
The system can be programmed to operate without Arm and Disarm chirp indications. When programmed  
for full-time silent operation, the siren will sound only when the system is triggered.  
The system is also capable of temporary silent operation when needed. Pressing button 4 then buttons 1  
or 2 will bypass the chirp confirmations for Arm/Disarm and allow one-time silent operation.  
Note: The open zone warning chirps will not be bypassed when the system is Armed or Disarmed silently.  
Anti-Carjacking Protection  
For a higher level of personal security, the system is equipped with three programmable Anti-  
Carjacking modes. When any Anti-Carjacking mode is triggered, the parking lights will flash twice  
to confirm activation. After 90 seconds the siren will begin chirping for 15 seconds as a warning,  
prior to entering full alarm mode. During the full alarm mode, the siren will sound, the parking  
lights will flash, and the horn will honk for up to five minutes or until the system is reset.  
Manual. When selected, activating the button 4 will automatically trigger the Anti-Carjacking feature. Press  
the button 4 again to reset the Manual Anti-Carjacking mode.  
Passive. When selected, the Anti-Carjacking feature will activate whenever a door is opened while the  
ignition is on. Press the Valet switch to reset the Passive Anti-Carjacking mode.  
G-20 - Page 7  
 
System Programming  
Entering System Programming  
To enter System Programming:  
1. Turn on ignition.  
2. Within 5 seconds, press the valet switch 5 times.  
· The siren will provide one long chirp, indicating that you have entered Programming.  
3. Press the valet switch the number of times equal to the System Parameter you want to change.  
· The siren will chirp each time the valet switch is pressed.  
4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for  
that System Parameter.  
· The siren will chirp to indicate the setting.  
1 chirp  
2 chirps  
3 chirps  
=
=
=
Button 1  
Button 2  
Button 3  
5. When you are finished, turn off the ignition to save the changes.  
Default Reset  
Following this procedure will set all System Programming Parameters to factory default settings.  
1. Enter System Programming.  
2. Press Transmitter Button 3.  
· The siren will chirp 6 times indicating that the reset signal was received.  
· All System Programming parameters are now set to factory default settings.  
· The Valet Mode is off.  
3. Turn off ignition.  
Programmable System Options  
Branch Feature  
1. Horn Chirps w/ Arm&Disarm  
2. Arm Mode  
3. Passive Door Locking  
4. Ignition Controlled Locks  
5. Door Input Monitoring  
6. Auto Rearming  
7. Door Unlock Pulse  
8. Arming Chirps  
Button 1 (default)  
Horn Chirps Disabled  
Manual Arming  
Disabled  
Button 2  
Button 3  
Horn Chirps Enabled Horn Chirps w/Warn  
Passive Arming  
Enabled  
Off  
60 Seconds  
Enabled  
Double  
Passive w/Countdown  
Set Override Code  
Lock Only  
On  
10 Seconds  
Disabled  
Single  
Normal  
Silent  
9. Extended Parking Lights  
10. Disarm with Aux 1  
11. Door Lock Pulse Length  
12. Anti-Carjack Mode  
13. Anti-Carjack Type  
14. Ignition Armed Mode  
15. Interior Light Mode  
On  
Disabled  
1 Second  
Disabled  
Manual  
Disabled  
Interior Light 30Sec  
Off  
Enabled  
3 Seconds  
Enabled  
Passive  
Enabled  
Windows 10Sec  
0.1 Seconds  
Full-time  
Windows 30Sec  
Page 8 - G-20  
G-20 - Page 8  
 
1. Horn Chirps with Arm & Disarm. Selects one of three modes: Normal, Horn Chirps, and Horn  
Chirps w/Warn.  
Normal. When selected, the horn will honk only when the alarm is triggered.  
Horn Chirps. When selected, the horn will provide the arm/disarm and trigger indications, allowing the  
siren installation to be skipped.  
Horn Chirps w/Warn. When selected, the horn will provide arm/disarm, trigger, and warn-away  
indications.  
2. Arm Mode. Selects one of three modes: Manual Arming or Passive Arming, and Passive Arming  
w/Countdown. With the Passive Arming w/Countdown mode selected, the siren will chirp every 2  
seconds while counting down until the system passively arms. Note: If Auto Rearming is selected, the  
siren will also chirp during Auto Rearm countdown.  
3. Passive Door Locking. Selects whether or not the system will automatically lock the doors during  
passive arming.  
4. Ignition Controlled Locks. Selects whether or not the system will lock and unlock the doors with the  
ignition.  
5. Door Input Monitoring. Selects whether the system begins monitoring the door inputs after 10  
seconds or 60 seconds. For vehicles with interior lights that remain on for an extended period of time  
after the doors are closed, set for 60 seconds.  
6. Auto Rearming Mode. When selected, the system will automatically re-arm and lock 30 seconds after  
it is disarmed if the doors have not been opened.  
7. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output.  
Vehicles that require two pulses on the proper wire to unlock the doors can be interfaced directly  
without the use of relays or any additional circuitry by programming the system for double unlock pulse.  
8. Arming Chirps. Selects between normal and silent operation.  
9. Extended Parking Lights. When selected, the parking lights will remain on for 30 seconds after  
disarming the system.  
10. Disarm with Auxiliary 1. When selected, activating the Auxiliary 1 output (usually used to open the  
trunk) will disarm the alarm.  
11. Door Lock Pulse Length. Selects between a 1-second and a 3-second output for door locking and  
unlocking. Program to 3 seconds for vehicles equipped with vacuum door locking systems.  
12. Anti-Carjack Mode. Enables Anti-Carjacking protection.  
13. Anti-Carjack Type. Selects one of three modes for Anti-Carjacking: Active, Passive, or Full-Time.  
Manual. When selected, activating the Panic feature will automatically engage the Anti-Carjacking  
feature.  
Passive. When selected, the Anti-Carjacking feature will activate whenever a door is opened while the  
ignition is on.  
Full-Time. When selected, the Anti-Carjacking feature will automatically activate each time the ignition  
is turned on.  
14. Ignition Arm Mode. Ability to Arm the system with Ignition in On position.  
15. Interior Light Mode.  
Interior Light 30Sec - Upon Disarming, Interior Light Output turns ON for 30 Sec.  
Windows 10Sec - Upon Arming, Interior Light Output turns ON for 10 Sec.*  
Windows 30Sec - Upon Arming, Interior Light Output turns ON for 30 Sec.*  
* For Optional Window Rollup Module.  
Page 9 - G-20  
G-20 - Page 9  
 
Door Lock Diagrams  
Adding Actuators  
Negative Trigger  
Reverse Polarity  
Positive Trigger  
blue  
green  
Starter Interrupt  
Positive Horn Honk  
Page 10 - G-20  
 
Wiring Diagram  
Shock Sensor  
Green - Lock Out (-) 500mA  
Blue - Unlock Out (-) 500mA  
Valet Switch  
LED  
Orange - Ground when Armed Output (-) 500mA  
Blue - Hood/Trunk Trigger Input (-)  
Black/White -Domelight Activation Output (-)500mA  
Brown/White - Horn Output (-)500mA  
Gray - Auxiliary 1 Output (-)500mA  
Brown - Siren Output (+)3A  
Blue  
Red  
Control Unit  
G-20  
Green - Door Trigger Input (-)  
Purple - Door Trigger Input (+)  
White - Parking Light Output (+)10A  
Red - +12V Battery Input (+)  
Yellow -+12v Ignition Input  
ScyTek Electronics  
11627 Cantara Street  
North Hollywood, CA 91605  
© ScyTek Electronics 2009  
G-20 4-11-09  
 

Pyramid Car Audio Stereo Equalizer 903G User Guide
Radio Shack Battery Charger 23 322 User Guide
Razor Mobility Scooter v1_09 11 User Guide
RCA Universal Remote RCR311S User Guide
Renault Automobile Parts 852 User Guide
Renesas Switch HD74CBT1G126 User Guide
Samsung Flat Panel Television LC550 ZA User Guide
Sanyo Cordless Telephone CLT J40 User Guide
Sears Lawn Mower 24737638 User Guide
Sears Microwave Oven 565661 User Guide