ASTRA 777-TC
WITH TRUE COLOR REMOTE
VEHICLE SECURITY SYSTEM
PRODUCT MANUAL
Table of Contents
1.
2.
About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1
Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2-11
2-way LCD Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Adding/Replacing 2-way LCD Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Setting The Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Setting The Alarm Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
LCD Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
System Confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
Transmitter Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
LCD Icon Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
Silent Arming/Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 19
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20
Optional Coded Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20
Automatic Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21
Driver Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 21
3.
4.
5.
Extended Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Ignition Controlled Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Dome Light Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Disarm with Auxiliary Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Remote Sensor Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Anti-Carjacking Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
6.
7.
System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23
Mounting the Control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 24
Mounting the Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 24
Mounting the Shock Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 24
System Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 25
14-Pin Main Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 25
3 Pin Door Lock Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 25
Plug-in Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 26
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 26
8.
System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27
Entering System Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27
Default Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27
Programmable System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 27
Branch Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 29
9. Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 30
10.
11.
12.
Two Stage Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 31
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 33
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Page
About Your System
Congratulations on your purchase of this state-of-the-art vehicle security system from ScyTek
Electronics. With proper installation this system will provide superior protection and performance
for many years to come.
System Contents:
• Main Unit
• One 5-Button 2-Way LCD Remote Transmitter
• One 5-Button Random Code Remote Transmitter
• 2-Way Pager Transceiver Antenna
• High Output 6-tone Siren
• Dual Stage Shock Sensor
• Status LED
• Coded Emergency Override/ Valet Switch/Call Button built into the antenna(See Page 23)
*
Options and Accessories
This ScyTek system includes several optional inputs and outputs allowing the creation of a
completely personalized security and convenience system by offering many optional features
such as:
*May require additional parts and/or labor, see store for details.
· Second Car Operation
· Remote Door Locking
· Two Stage Door Unlocking
· Starter Defeat
· Horn Honk
· Illuminated Entry
· Remote Car Start
· Power Trunk / Hatch Release
· Glass Breakage Sensor
· Radar Sensor
· Auxiliary Lighting Control
· Back-up Battery Siren
· Remote Window Control
PLEASE NOTE:
Some of the features described in this manual may require additional parts and/or labor, and may not be included
as part of the standard installation of this unit. Additionally, many features of this security system have
selectable options that must be activated or programmed during the system’s installation. These items will be
identified in the following sections. Please discuss these features and any questions you may have regarding the
installation of this product with Your Authorized Dealer.
Astra 777-TC - Page 1
2-WAY COLOR LCD REMOTE TRANSMITTER DESCRIPTION
time
date/engine run timer
11/16
3:10P
Button 3
Button 4
Button 5
Button 2
wakeup
alarm
enabled
Button 1
Battery
status
autostart
enabled
The 2-way Color remote transmitter is offering increased range and confirmation of any activated feature.
Page 1
Button 1 Arms and Locks* the system and when held for 3 seconds, activates the system’s Panic feature.
Button 1 also locks the doors when the system is in Valet Mode.
Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock feature
(if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Button 3 Activates the Auxiliary 1 output normally used for trunk release (note trunk icon on button).
Button 4 Activates the Remote Start feature.
Button 5 is the Confirmation, Programming and the Page Shift button. Quickly pressing button 5 will activate
the Page 2 function. Pressing button 5 for 2 seconds activates the system’s confirmation feature which
will then display the current status of the system (armed, disarmed, engine running, etc.).
Page 2
Button 1 Silently Arms*/Locks the system.
( * press and release button 5 then press button 1)
Button 2 Silently Disarms*/Unlocks the system. ( * press and release button 5 then press button 2)
Button 3 Activates the Auxiliary 2 output.
( * press and release button 5 then press button 3)
( * press and release button 5 then press button 4)
Button 4 Aux 3 or Factory Rearm output.
Button 5 not used
Page 3 & 4 are used as Page 1 & 2 for second car operation
System Confirmation
The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time.
To display system status:
1. Press and hold Button 5 until the display shows CONFIRM.
· The transmitter will beep once.
2. Release Button 5.
· The transmitter will beep once.
· The panel will display the current system status.
Page 2 - Astra 777-TC
PAGER PARAMETERS SETTING
Press and hold Buttons 2 and 3 until pager program features are displayed.
Select pager setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the pager.
Setting Date & Time
Select Time Date setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
TIME DATE
START TIME
ALARM CLOCK
SOUND ON
BACK
Use buttons 1 & 2 to highlight the parameter you wish to change, use buttons 3 & 4 to scroll up or down
to chage the time or date. Save the changes by pressing button 5.
11/14
12:00P
TIME: 04:12P
DATE: 11/24
Setting AutoStart Time
Select Start Time setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
TIME DATE
START TIME
ALARM CLOCK
SOUND ON
BACK
Enable/Disable Auto Start
Select Auto Start on/off by pressing button 3.
Symbol is displayed if the Auto Start feature when enabled.
START SET
AUTO ST ON
TIME: 08:00A
Astra 777-TC - Page 3
Use buttons 1 & 2 to highlight the time parameter you wish to change, use buttons 3 & 4 to scroll up or
down to chage the time. Save the changes by pressing button 5.
START SET
AUTO ST ON
TIME: 08:00A
Setting Alarm Clock
Select Alarm setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
TIME DATE
START TIME
ALARM CLOCK
SOUND ON
BACK
Enable/Disable Alarm
Select Alarm Clock on/off by pressing button 3.
CLOCK ALARM
ALARM ON
TIME: 08:00A
Use buttons 1 & 2 to highlight the time parameter you wish to change, use buttons 3 & 4 to scroll up or
down to chage the time. Save the changes by pressing button 5.
CLOCK ALARM
ALARM ON
TIME: 08:00A
Symbol is displayed when Alarm Clock is enabled.
Selecting Sound/Vibration
Select Sound/Vibration setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select
it.
TIME DATE
START TIME
ALARM CLOCK
SOUND ON
BACK
Page 4 - Astra 777-TC
Return to Previous Screen
Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
TIME DATE
START TIME
ALARM CLOCK
SOUND ON
BACK
Set System Parameters
Press and hold Buttons 2 and 3 until pager program features are displayed.
Select system setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the
system features.
Siren Chirp Enable/Disable
Select Siren Chirp setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
SIREN CHIRP
PASSIVE ARM
COLD TEMP
HOT TEMP
BACK
Sytem Responce
FEATURE ON
Passive Arm Enable/Disable
Select Passive Arm setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
SIREN CHIRP
PASSIVE ARM
COLD TEMP
HOT TEMP
BACK
Sytem Responce
FEATURE ON
Astra 777-TC - Page 5
Setting AutoStart Cold Temperature Threshold
Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select
it.
SIREN CHIRP
PASSIVE ARM
COLD TEMP
HOT TEMP
BACK
Use buttons 3 & 4 to scroll up or down to chage the temperature threshold. Save the changes by
pressing button 5.
AUTOSTART
SET
COLD TEMP
o
TEMP: - 11 F
Security system responce
Setting AutoStart Hot Temperature Threshold
Select Cold Temp Time setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to
select it.
SIREN CHIRP
PASSIVE ARM
COLD TEMP
HOT TEMP
BACK
Use buttons 3 & 4 to scroll up or down to chage the temperature threshold. Save the changes by
pressing button 5.
AUTOSTART
SET
HOT TEMP
o
TEMP: 110 F
Security system responce
Page 6 - Astra 777-TC
Synchronize System and Pager Clocks
Select Clock Sync setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the
pager.
Pager Clock Sync
This feature synchronizes the pager clock to the security system time of a day clock.
Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
AUTO
PGR CLK SYNC
CLOCK SET
SYS CLK SYNC
START 1 TIME
START 2 TIME
EXIT
Security system responce
System Clock Sync
This feature synchronizes the system clock to the pager time of a day clock.
Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
PGR CLK SYNC
SYS CLK SYNC
SYSTEM
CLOCK SET
START 1 TIME
START 2 TIME
EXIT
Security system responce
Start Time 1
This feature sets the system Autostart 1 time.
Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
PGR CLK SYNC
SYS CLK SYNC
START 1 TIME
START 1 SET
SET TIME
START 2 TIME
EXIT
TIME: 8:00A
Use buttons 1 & 2 to highlight hours or minutes, use buttons 3 & 4 to scroll up or down to chage the
time.
Astra 777-TC - Page 7
START 1 SET
SET TIME
TIME: 8:00A
Use buttons 1 & 2 to highlight Set Time press button 3.
AUTOSTART 1
TIME: 8:00A
The security system responce.
Start Time 2
This feature sets the system Autostart 2 time.
Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
PGR CLK SYNC
SYS CLK SYNC
START 1 TIME
START 2 TIME
EXIT
Use buttons 1 & 2 to highlight hours or minutes, use buttons 3 & 4 to scroll up or down to chage the
time.
START 2 SET
SET TIME
TIME: 8:00A
Use buttons 1 & 2 to highlight Set Time press button 3.
START 2 SET
SET TIME
TIME: 8:00A
The security system responce.
AUTOSTART 2
TIME: 8:00A
Recall Alarm History
11/16
3:10P
Select Alarm History by pressing buttons 3 or 4 to highlight the feature. Press button 1 to select it.
Page 8 - Astra 777-TC
Programmable Functions using the Color Remote
Pressing and holding transmitter button 5 will scroll through several transmitter programmable
options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE,
ENABLE AUTOSTART 1, ENABLE AUTOSTART 2.
TEMPERATURE Check the temperature inside the vehicle
1. Press and hold Button 5 until the display shows TEMPERATURE
2. Release Button 5.
· The transmitter will beep four times.
ENABLE COLD START Auto Start Cold Temperature Activation Mode.
1. Press and hold Button 5 until the display shows ENABLE COLD START.
2. Release Button 5.
· The transmitter will beep.
· The display will show Auto Start Cold Temperature setting.
3. Press and hold Button 5 until the display shows CONFIRM.
4. Release Button 5.
· The transmitter will beep.
· The display will show "FEATURE ON" indicating that Auto Start Cold Temperature Activation
Mode is enabled.
ENABLE HOT START Auto Start Cold Temperature Activation Mode.
1. Press and hold Button 5 until the display shows ENABLE HOT START.
2. Release Button 5.
· The transmitter will beep.
· The display will show Auto Start Cold Temperature setting.
3. Press and hold Button 5 until the display shows CONFIRM.
4. Release Button 5.
· The transmitter will beep.
· The display will show "FEATURE ON" indicating that Auto Start Cold Temperature Activation
Mode is enabled.
VALET MODE Valet mode function sets and resets the security system valet mode.
** this function is enabled only when the system is disarmed/ unlocked.
Set or reset the Valet mode:
1. Press and hold Button 5 until the display shows VALET or DISARM.
· The transmitter will beep.
2. Release Button 5.
· The display will show VALET MODE .
· The transmitter will beep twice and the siren will chirp twice if the Valet
mode was reset. The symbol.
ENABLE AUTOSTART 1, ENABLE AUTOSTART 2
1. Press and hold Button 5 until the display shows ENABLE AUTOSTART 1 or
AUTOSTART 1
TIME: 8:00A
ENABLE AUTOSTART 2
2. Release Button 5.
· The transmitter will beep.
· The display will show Auto Start 1 or 2 time setting.
3. Press and hold Button 5 until the display shows CONFIRM.
4. Release Button 5.
AUTOSTART 2
TIME: 5:00P
· The transmitter will beep.
· The display will show "FEATURE ON" indicating that Auto Start 1 or 2 Activation
Mode is enabled.
Astra 777-TC - Page 9
ADDITIONAL FUNCTION
Transmitter Lockout
Press and hold buttons 2 & 4 simultanously for 3
seconds to lockout the transmitter against accidental
transmission.
Release Transmitter Lockout
Press and hold buttons 2 & 4 simultanously for 3 seconds
to release the transmitter from Lockout.
Out of Range Report
pager report if no responce from the unit.
ICONS
Transmitter
Unlocked
Transmitter
Locked
Disarmed
Valet
Armed
Ring
Alarm
Alarm Sensor
Warnaway
Alarm Trunk
Alarm Hood
Alarm Door
Temperature
Set
Temperature
read
Engine Start
Engine Run
Engine Stoped
Engine Start
Page 10 - Astra 777-TC
Pager Status Display
Time: time of day clock
Date/Engine Run Timer: date, or engine run minute timer if remote start activated (20 min
max).
Battery Status: displays remaining battery life.
Wakeup Alarm: displays Wakeup alarm enabled
Autostart: Remote Start Autostart enabled
Transmit: Pager transmission in progress
time
date/engine run timer
11/16
3:10P
System Status
wakeup
alarm
enabled
Battery
status
autostart
enabled
Astra 777-TC - Page 11
2-way LCD Remote Transmitter Description (Optional)
Button 1
Button 2
Button 3
Button 4
Button 5
The Astra’s 777-TC 2-way LCD remote transmitter is offering increased range and confirmation of any
activated feature.
Page 1
Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature.
Button 1 also locks the doors when the system is in Valet Mode.
Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock feature
(if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Button 3 Activates the Auxiliary 1 output normally used for trunk release (note trunk icon on button).
Button 4 Activates the Auxiliary 2 output.
Button 5 is the Confirmation, Programming and the Page Shift button. Quickly pressing button 5 will activate
the Page 2 function. Pressing button 5 for 2 seconds activates the system’s confirmation feature which
will then display the current status of the system (armed, disarmed, engine running, etc.).
Page 2
Button 5 then Button 1 : Silently Arms and Locks* the system. Button 1 also locks the doors when the
system is in Valet Mode.
Button 5 then Button 2: Silently Disarms and Unlocks* the system, also unlocks the doors when the system
is in Valet Mode.
* If the Optional Keyless Entry Feature is installed.
Page 12 - Astra 777-TC
Adding/Replacing 2-way LCD Transmitters (2 LCD remotes maximum)
When adding an optional 2-way LCD transmitter to the system, follow these steps:
1. Turn on the ignition key On, Off, On, Off, On, Off, and back On. (Key On 4 times)
· The siren will chirp 4 times.
2. Press and hold the Override switch for 5 seconds.
· The siren will chirp 4 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter, then on the second transmitter.
· The siren will chirp once for each transmitter learned.
4. Turn off the ignition key.
5. The siren will chirp 3 times to indicate the system has exited programming mode.
LCD Transmitter Battery Replacement
Your Astra Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
Depending on the amount of use, the battery may last up to three months before it needs replacement.
When the battery needs replacing, the system’s operating range will decrease, the LCD display will show
only one of three bars in the battery icon, or the display and sounds may suddenly stop and start as the
battery voltage drops below minimum.
In order to change the battery, first slide the battery door locking pin to the side. Carefully slide the battery
cover downward until it is free. While replacing the battery make sure that the positive and negative
terminals are positioned correctly, then carefully reassemble the transmitter case.
Setting The Time
The LCD display is equipped with a 12-hour clock that in addition to displaying the time, offers an alarm
clock function as well as a remote activation timer.
To set the time:
1. Press and hold Buttons 2 and 3 for three seconds.
· The remote will beep two times and three bars will be shown indicating time set mode is entered.
2. Press Button 2 until the correct hour is displayed.
3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster.
4. When the desired time is displayed, press Button 5 to store.
· The remote will beep 3 times to indicate the time has been set.
Setting The Alarm Clock
The alarm clock function can be set to play an alert melody at a specific time of day.
To set the alarm clock function:
1. Press and hold Buttons 2 and 3 until the remote beeps three times.
· The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered.
2. Press Button 2 until the desired hour is displayed.
3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster.
4. When the desired time is displayed, press Button 5 to store.
· The remote will beep 3 times to indicate the alarm clock has been set.
To disable the alarm clock function:
1. Press and hold Buttons 2 and 3 until the remote beeps three times.
· The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered.
2. Press Button 1 to disable the alarm clock.
· The remote will beep 3 times to indicate the alarm clock has been disabled.
Astra 777-TC - Page 13
LCD Backlight
Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of
the LCD backlighting for use in the dark. Press button 5 to activate the LCD backlight.
System Confirmation
The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed
at any time.
To display system status:
1. Press and hold Button 5 until the display shows CON.
· The transmitter will beep once.
2. Release Button 5.
· The transmitter will beep once.
· The icon representing the system’s current status will be displayed on the LCD panel.
Transmitter Programming
Pressing and holding transmitter button 5 will scroll through several transmitter programmable
options that may or may not be available depending on the model of system installed
DEG (degress) Not applicable on this model.
CHP Sets the siren confirmation chirps ON or OFF:
1. Press and hold Button 5 until the display shows CHP.
·The transmitter will beep 3 times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will show a siren if the chirps are enabled or "off" if the chirps are
disabled.
SND Sound function allows disabling of the transmitter's confirmation tones.
To turn the transmitter confirmation tones on or off:
1. Press and hold Button 5 until the display shows SND.
· The transmitter will beep four times.
2. Release Button 5.
· The transmitter will beep once.
· The LCD panel will beep five times if enabled or vibrate and display “off” if the
confirmation tones are disabled.
PSV Passive function allows the passive arming mode to be enabled oe disabled with the
transmitter.
Note: This feature may not be available on all systems.
To enable or disable the passive arming mode:
1. Press and hold Button 5 until the display shows PSV.
· The transmitter will beep five times.
2. Release Button 5.
· The transmitter will beep once and the system will begin the passive arm mode
· The LCD panel will display “off” and vibrate twice if disabled.
Page 14 - Astra 777-TC
VLT Valet mode function sets and resets the security system valet mode.
* this function is enabled only when the security system is disarmed
Set or reset the Valet mode:
1. Press and hold Button 6 until the display shows VLT.
· The transmitter will beep six times.
2. Release Button 5.
· The LCD panel will play a tone if the Valet mode was set “V" will be displayed indicating
that the system is in Valet mode.
· The transmitter will beep twice if the Valet mode was reset. “V" will turn off
indicating that the security system is out of Valet mode.
System Armed
Indicates the alarm is
ON.
System Disarmed
Indicates the alarm is
OFF.
Warn Away
Indicates the warn
away has been triggered. or auxilliary function
has been activated.
Trunk Release
Indicates the trunk
Door Open
Indicates the door zone
has been triggered.
Shock Sensor
Indicates the shock
sensor has been
triggered.
Battery Low
Trunk Open
Indicates the battery
inside the transmitter
needs to be replaced.
Indicates the trunk or
hood zone has been
triggerd.
Alarm clock
Indicates the
progammable timer
has been set.
Valet Mode
Panic
Indicates the system
has been placed in
valet mode.
Indicates the panic
mode has been
triggered.
Astra 777-TC - Page 15
Remote Transmitters
Remote Transmitter Description
LED
Button 1
Button 3
Button 2
Button 5
Button 4
The Astra 777-TC is supplied with one 5-button Remote Transmitter used to control system
operations.
Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic
feature. Button 1 also locks the doors when the system is in Valet Mode.
Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock
feature (if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Button 3 Activates the Auxiliary 1 output. This output will remain on for as long as the button is
pressed.
Button 4 Activates the Auxiliary 2 output. This output will remain on for as long as the button is
pressed.
Button 5 is the Page Shift button. The Page Shift button will change the function of Buttons 1
through 4 each time it is pressed, allowing access to additional features or multiple car operation.
Each time the Shift Button is pressed, the LED on the transmitter will illuminate and the
transmitter functions will shift to the next page, allowing access to another set of features. Once
shifted to another page (there are 4 pages total), the transmitter will remain on that page for 10
seconds or until a button is pressed, then return to page 1. Each time a transmitter button is
pressed and held, the LED will flash a number of times to indicate from which page it is
transmitting. Under normal operation, only pages 1 and 2 are used. Pages 3 and 4 are usually
used for Two Car Operation (see page 3).
Shift then Button 1 Arms and Locks* the system silently.
Shift then Button 2 Disarms and Unlocks* the system silently.
* If the Optional Keyless Entry Feature is installed.
Page 16 - Astra 777-TC
Adding/Replacing One-Way Transmitters
To replace lost or stolen transmitters or to add additional transmitters into the system, have all
desired transmitters ready and follow the steps below.
Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously
stored transmitter code will be erased if it is not programed within the following sequence.
To program the transmitter(s):
1. Turn on the ignition key On, Off, On, Off, and back On.
· The siren will chirp 3 times.
2. Press and hold the Override switch for 5 seconds.
· The siren will chirp 5 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter.
· The siren will chirp once.
4. Press Button 1 on the first transmitter again.
· The siren will chirp twice to indicate it has learned the code.
5. Repeat steps 3 and 4 for each transmitter (up to 4).
6. Turn off the ignition key.
Two Car Operation
If two vehicles are equipped with Astra 777-TC systems, for convenience both can be operated
using the same remote transmitter. If all four transmitters are to be used with both cars,
program transmitters A and B into the first vehicle in the manner described above. Program
transmitters C and D by pressing the Shift button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second
vehicle as normal, then program transmitters A and B by pressing the Shift button twice before
performing steps 3 and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle
by pressing the Shift button twice and the desired function button.
Battery Replacement
Your Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will require
replacement in time. Depending on the amount of use, the battery may last up to six months
or more before it needs replacement.
When the battery needs replacing, the system’s operating range will decrease or the transmitter
LED may not be as bright.
In order to change the battery, first remove 2 screws from the back of the transmitter and
separate the top and bottom halves of the case.
While replacing the battery make sure that the positive and negative terminals are positioned
correctly, then carefully reassemble the transmitter case.
Astra 777-TC - Page 17
System Operation
Remote Arming
The system monitors 4 independent areas (zones) while armed: doors, hood/trunk, shock
sensor and optional sensor input.
To Arm the System:
1. Turn off the ignition.
2. Press Button 1.
· The siren will chirp once.*
· The doors will lock.
· The parking lights will flash once.
· The LED will turn on, to indicate the starter defeat is activated.
3. 5 seconds after Arming:
· The LED will start blinking to indicate that the doors and hood/trunk inputs are being
monitored.
* During Arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional
times and ignore that input, but keep all other areas protected.
Once Armed, the alarm will trigger when any of the following occurs:
· The doors are opened.
· The hood or trunk is opened.
· The shock sensor detects an impact to the vehicle.
· The optional sensor is disturbed.
When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will
flash. If the system is triggered by the doors, or hood/trunk, the system will alarm for 45
seconds. If triggered by the shock sensor or optional sensor input, the system will alarm
for 30 seconds.
In the event the alarm is triggered and remains triggered continuously by the same sensor
or input during a single arming cycle, that sensor or input will be automatically bypassed
until the next time the system is armed.
If the Shock Sensor detects a light impact to the vehicle, or the Optional Sensor’s warn-
away zone is disturbed, the siren will chirp 5 times as a warning indication.
Remote Disarming
To Disarm the System:
Press Button 2
· The siren will chirp twice.*
· The doors will unlock.
· The parking lights will flash twice and remain on for 30sec..
· The dome light will turn on.**
· The LED will turn off.
* During Disarming, if the system was triggered while away from the vehicle, the siren will chirp 3 times, the parking
lights will flash 3 times, and the LED will flash to indicate triggered zone. See Tamper Alert for zone listing.
** If the optional Dome Light Activation Feature is installed.
Page 18 - Astra 777-TC
Tamper Alert
If the system was triggered while away, the LED will flash to indicate which zone triggered the
system after disarming and turning on the ignition. The LED indication will repeat 8 times.
LED Flashes:
1 flash
=
=
=
=
=
=
optional sensor
shock sensor
not used
door
2 flashes
3 flashes
4 flashes
5 flashes
10 flashes
trunk
main power interrupt or system was reset
example: flash-flash-pause-flash-flash-pause = shock sensor
Silent Arming/Disarming
The system can be programmed to operate without Arm and Disarm chirp indications. When
programmed for full-time silent operation, the siren will sound only when the system is triggered.
The system is also capable of temporary silent operation if desired. Pressing the Shift button
before Arming or Disarming the system will bypass the chirp confirmations and allow one-time
silent operation.
Note: The open zone warning chirps will not be bypassed when the system is Armed or Disarmed silently.
Passive Arming
When programmed for the optional Passive Arming feature, the system arms itself automatically,
each time the ignition is turned off and all of the doors, hood, and trunk are closed.
To start the Passive Arming Process:
1. Turn off the ignition.
2. Open the door and exit the vehicle.
· Once all doors are closed and the dome light is off, the LED will begin flashing rapidly.
Parking Lights will flash twice three seconds after passive arming cycle began.
3. After 30 seconds,
· The siren will chirp.
· The parking lights will flash.
· The doors will lock.*
· The status LED will begin flashing.
4. The system is now armed.
* If the Passive Locking feature is selected.
Astra 777-TC - Page 19
Panic Mode
In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly
trigger the alarm.
To activate the Panic Mode:
1. Press and hold Button 1 for 5 seconds.
· The alarm will sound.
· The parking lights will flash.
· The doors will unlock* allowing access to the vehicle.
2. Press Button 2 to stop Panic Mode.
* If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.
Emergency Override
If the transmitter becomes lost or inoperable, the system can still be disarmed using the following
procedure. Before beginning this procedure be sure to have the ignition key ready and know the
location of the override switch.
To Emergency Override the system:
1. Unlock the door using the key.
2. Enter the vehicle.
· The system will trigger and the siren will sound.
3. Turn the ignition key on.
4. Press and hold the override switch until the system disarms.
5. The vehicle will now be able to start.
Optional Coded Emergency Override
As an extra measure of security, the system is equipped with an optional Coded Emergency
Override feature. Once an Emergency Override Code is chosen and programmed during
installation, the system can no longer be disarmed using the standard override procedure.
To Emergency Override the system using the Code:
1. Follow steps 1-3 above.
2. Press the override switch a number of times equal to the Disarm code, and continue
holding for 10 seconds on the last press.
· The system will disarm. If the code is entered incorrectly, turn off the ignition and
begin again.
To set the Emergency Override Code:
1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.
· The siren will provide one long chirp, indicating that you have entered Programming.
3. Press the valet switch 4 times.
· The siren will chirp each time the valet switch is pressed.
4. Within 5 seconds, press Button 3 on the transmitter.
· The siren will chirp 3 times.
5. Press the valet switch the number of time equal to the desired code (from 1-15).
Page 20 - Astra 777-TC
6. Turn off the ignition then arm the system.
7. Disarm the system using the new Override Code to permanently store the new code.
Note: If the code set procedure is not properly performed, turn off the ignition and begin again. The override
code will not be permanently stored until the code is used to disarm the system.
Automatic Rearming
The Automatic Rearming feature is designed to protect the vehicle in the event the system is
accidentally disarmed.
With the Automatic Rearming feature enabled, the alarm will
automatically rearm and lock 30 seconds after disarming.
* Note Door open trigger does not stop the Rearm Cycle
Valet Mode
The Valet Mode temporarily disables the security system so the vehicle may be operated by a
mechanic or parking attendant.
To activate or deactivate the Valet Mode:
1. Turn on the ignition.
2. Press and hold the override switch for 5 seconds.
· The siren will chirp once and the LED light will stay ON to confirm the Valet Mode is
on.
· The siren will chirp twice and the LED light will turn OFF to confirm the Valet Mode is
off.
3. Turn off the ignition.
While in Valet Mode the remote transmitters will continue to lock and unlock the doors, and
operate the optional auxiliary functions.
DRIVER CALLING/PAGE FEATURE
The Astra 777-TC is equipped with a Driver Calling or Paging feature that allows the system to send
a page to the LCD transmitter in the event the transmitter has been misplaced or lost (within 1500 feet)
To activate the Driver Calling/Page feature:
1.Locate the Valet/Emergency Override button in your vehicle (Ask your installation shop)
· With the ignition switch OFF, press and hold the Valet/Emergency override button for 2
seconds, then release.
· The LCD transmitter will beep continually and the “DRIVER CALLING” icon will appear
· Press and release button 5 to turn off transmitter page.
Astra 777-TC - Page 21
Extended Features
Ignition Controlled Door Locks
For added safety, the Ignition Door Locking feature allows vehicles equipped with power door
lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors
after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition
locking feature is disabled to protect against locking the keys inside the vehicle.
Dome Light Activation
If the optional Dome Light Activation feature is installed, the dome light will turn on when the
system is disarmed using the Remote Transmitter. The dome light will remain on for 30 seconds
or until the ignition is turned on.
Auxiliary Function Outputs
The Astra 777-TC system is equipped with 2 Auxiliary Outputs allowing the convenience features
of the system to be further expanded. These outputs can be used to add a number of optional
features such as: power trunk release, remote engine start, power window activation, power
sunroof control, and more.
Disarm with Auxiliary Function
If Auxiliary 1 is installed to activate the vehicle’s trunk release, the system can be programmed
to automatically disarm the alarm when the trunk is opened using the transmitter. In this
manner, the trunk can be accessed without first disarming the alarm.
Remote Sensor Disable
When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong
weather conditions that could cause the sensors to trigger, the sensor inputs can be temporarily
bypassed using the Remote Transmitter, preventing possible false alarms.
To disable the sensor inputs :
1. Arm the system normally.
2. Within 5 seconds of Arming the system, press the Arm button again.
· The siren will chirp 5 times and the parking lights will flash 5 times to indicate the sensors are disabled.
· The sensors will remain disabled until the next arming cycle.
Anti-Carjacking Protection
For a higher level of personal security, the system is equipped with three programmable Anti-
Carjacking modes. When any Anti-Carjacking mode is triggered, the parking lights will flash twice
to confirm activation. After 90 seconds the siren will begin chirping for 15 seconds as a warning,
prior to entering full alarm mode. During the full alarm mode, the siren will sound, the parking
lights will flash, and the horn will honk for up to five minutes or until the system is reset.
Manual. When selected, pressing Button 4 of one way remote, or page 2 button 3 of the LCD remote, with
the ignition ON will automatically trigger the Anti-Carjacking feature. Press the Button again to reset the
Manual Anti-Carjacking mode.
Passive. When selected, the Anti-Carjacking feature will activate whenever a door is opened while the
ignition is on. Press the Valet switch 1 time to reset the Passive Anti-Carjacking mode.
Full-Time. When selected, the Anti-Carjacking feature will automatically activate each time the ignition is
turned on. Press the Valet switch 1 time while the ignition is on to reset the Passive Anti-Carjacking mode.
Note: The desired Anti-carjacking mode must be programmed during installation.
Page 22 - Astra 777-TC
System Installation
1. Thoroughly read and become familiar with the installation instructions before beginning the
installation.
2. Review system contents:
Main Unit
1 One-Way 5-Button Remote Transmitter
1 Two-Way 5 Button LCD Transmitter
Siren
Shock Sensor
Harnesses
Reciever Antenna
• 14-Pin main harness
• 4-Pin shock sensor harness
• 3-Pin door lock harness
• LED harness
• Valet Switch harness
• Receiver Harness
3. Verify with the owner, the mounting locations for all visible components, including the LED
and Override switch.
4. Verify with the owner, the optional features of the Astra 777-TC and the functions that must
be programmed during installation.
5. Inspect and perform a function test of all vehicle systems before and after the installation.
6. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light.
7. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel lines and
exterior wiring looms are clear as they are often close to the chassis and difficult to see.
8. Protect all wires running from the engine compartment to the interior of the vehicle by
covering with electrical tape and split loom tubing. Be sure to use a grommet when routing
wires through the firewall.
9. Properly fuse any additional accessories such as window modules, door lock actuators, etc.,
making sure to power them separate from the alarm module. This will ensure the
functionality of the security system in the event of an accessory failure.
Astra 777-TC - Page 23
Mounting the Control Unit
The control unit must only be mounted in the interior of the vehicle. Do not mount the
main unit in the engine compartment. Choose a mounting location that will not be easily
accessible to a thief, and will not interfere with the operation of any vehicle components
such as foot pedals, steering column, air vents, seat rails, etc.
Do not mount the control unit until after setting the internal jumpers and performing a
complete operation check of the system. After installation is complete and performance
verified, the control unit can be easily mounted using wire ties through the mounting tabs
on the bottom of the unit.
Mounting the Siren
Choose a siren mounting location that is away from heat sources such as exhaust manifolds,
and where it cannot be easily accessed from underneath the vehicle. Be sure to face the
siren downward to prevent the collection of water in the siren’s housing.
Always route all wires from the engine compartment into the interior of the vehicle through
a proper grommet.
Mounting the Shock Sensor
Choose a suitable interior mounting location for the shock sensor that provides ample
coverage of the vehicle. Keep the sensor away from the vehicle’s ECM or other sources of
electrical interference. Suggested mounting locations include air conditioning ducts,
dashboard braces, or center console supports.
During proper operation, the shock sensor will detect impacts to the vehicle only and will
not usually be triggered by slow rocking movements of the vehicle like those caused by
wind.
Page 24 - Astra 777-TC
System Wiring
14-Pin Main Harness
Pin 1 RED WIRE: +12V Battery Input (15A Fuse). The RED wire must be connected to a clean source of
continuous +12V power.
Pin 2 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows
+12V or ground only when the parking lights are on and set the internal parking light relay jumper to
the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with
independent left and right parking light circuits, diodes must be installed to keep the circuits separate.
NOTE: Do not connect the WHITE wire to the vehicle’s headlight circuit.
Pin 3 BROWN WIRE: Siren Output (+) 3A. The BROWN wire must connect to the siren’s red wire. The
BLACK siren wire must be grounded.
Pin 4 BLUE/WHITE: Passenger Unlock output (-) 500mA. Connect to an optional relay to unlock the
passenger doors for two-stage unlock (see Two Stage Door Lock Diagrams).
Pin 5 WHITE/RED WIRE: Auxiliary 2 Output (-) 500mA. Connect to a relay or module for an optional
feature such as power window activation or remote start, etc.
Pin 6 ORANGE WIRE: Armed Output (-) 500mA. The ORANGE wire provides a ground output while armed
to activate an optional starter defeat relay or other device such as a power window control module.
Pin 7 BROWN/WHITE WIRE: Horn Output (-) 500mA. Connect to an optional relay to activate the
vehicle’s horn when the alarm is triggered.
Pin 8 BLACK/WHITE WIRE: Dome Light Output (-) 500mA. Connect to an optional relay for dome light
activation.(See GREEN and VIOLET door trigger wires).NOTE: MUST USE RELAY
Pin 9 BLUE WIRE: Trunk/Hood trigger Input (-). Connect the BLUE wire to the trunk and/or optional hood
pin switches. The switch must provide a ground output when opened.
Pin 10 GRAY WIRE: Auxiliary 1 Output (-) 500mA. Connect to a relay or module for an optional feature
such as trunk release, etc.
Pin 11 YELLOW WIRE: +12V Ignition Input. The YELLOW wire must connect to a main ignition wire at the
ignition harness. This wire must show +12V when the ignition is on.
Pin 12 BLACK WIRE: Ground Input (-). The BLACK wire must connect to a solid chassis ground. Clean away
any paint or dirt to insure the best possible ground.
Pin 13 VIOLET WIRE: Positive door trigger Input (+). Connect to the door switch circuit wire that shows
+12V when the door is open. This type of door circuit is usually found on Ford vehicles.
Pin 14 GREEN WIRE: Negative door trigger Input (-). Connect to the door switch circuit wire that shows
ground when the door is open.
Astra 777-TC - Page 25
Plug-in Connectors
3-Pin White Door Lock Connector: Plug-in connector port for door lock harness or optional door lock
relay module.
· BLUE WIRE - negative unlock output (-) 500mA.
· GREEN WIRE - negative lock output (-) 500mA.
2-Pin Red Connector: Plug-in connector port for LED. Mount the LED in an area where it may be easily
seen from either side of the vehicle.
2-Pin Blue Connector: Plug-in connector port for valet switch. Mount the valet switch in an area that is
easily accessible from the driver’s position.
4-Pin White Connector : Plug-in connector port for dual stage shock sensor.
Jumper Settings
Jumper Selection
Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking
light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity
output as described below, then reassemble the main unit case.
Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay.
Left Pin + Center Pin = positive
Right Pin + Center Pin = negative
default setting shown
Page 26 - Astra 777-TC
System Programming
Entering System Programming
To enter System Programming:
1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.
· The siren will provide three chirps, indicating that you have entered Programming.
3. Press the valet switch the number times equal to the System Option you want to change.
· The siren will chirp each time the valet switch is pressed.
4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for
that System Option.
· The siren will chirp to indicate the setting.
1 chirp
2 chirps
3 chirps
=
=
=
Button 1
Button 2
Button 3
5. When you are finished, turn off the ignition to save the changes.
Default Reset
Following this procedure will set all Programmable System Options to factory default settings.
1. Enter System Programming.
2. Press Transmitter Button 3.
· The siren will chirp 6 times indicating that the reset signal was received.
· All Programmable System Options are now set to factory default settings.
· The Valet Mode is off.
3. Turn off ignition.
Programmable System Options
The following is a description of the programming options. Some program branches control more than one
option, and may require accessing a particular branch number twice in order to program all desired features.
1. Horn Chirps with Arm & Disarm. Selects one of two modes: Normal, Horn Chirps
Normal. When selected, the horn will honk only when the alarm is triggered.
Horn Chirps. When selected, the horn will provide the arm/disarmed trigger indications, allowing the siren
installation to be skipped.
2. Arm Mode. Selects one of two modes: Manual Arming or Passive Arming.
3. Passive Door Locking. Selects whether or not the system will automatically lock the doors during
Passive Arming.
4. Ignition Controlled Locks/ Override Code Set. This dual program branch sets Ignition Controlled
Locking and programs the optional Emergency Override Code. If Lock Only is selected, the doors will not
automatically unlock when the ignition is turned off.
Override Code Set. Changes the Emergency Override Code for a higher level of security (see page 7).
5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when
the ignition is turned off. The Ignition Door Locking feature may be programmed to unlock all doors or
the driver’s door only. If driver’s door only is selected, the optional Passenger Unlock feature must be
connected. (See Two Stage Door Lock Diagrams)
Astra 777-TC - Page 27
6. Ignore Open Door Report. Bypasses the open zone warning chirps for vehicles equipped with a
residual dome light circuit that remains ON for a period of time after closing the door.
7. Auto Rearming Mode. When selected, the system will automatically re-arm and lock 30 seconds after
it has been disarmed regardless if a door is open or closed.
8. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output.
Vehicles that require two pulses on the proper wire to unlock the doors can be interfaced directly without
the use of relays or any additional circuitry by programming the system for double unlock pulse.
9. Arming Chirps. Selects between normal and silent operation.
10. Disarm with Auxiliary 1. When selected, activating the Auxiliary 1 output (usually used to open the
trunk) will disarm the alarm.
11. Door Lock Pulse Length. Selects between a 1, 3 or 0.1 second output for door locking and unlocking.
Program to 3 seconds for vehicles equipped with vacuum door locking systems.
12. Anti-Carjack Type. Selects one of three modes for Anti-Carjacking: Active, Passive, or Full-Time.
Manual. When selected, pressing Button 4 will automatically engage the Anti-Carjacking feature.
Passive. When selected, the Anti-Carjacking feature will activate whenever a door is opened while the
ignition is on.
Full-Time. When selected, the Anti-Carjacking feature will automatically activate each time the ignition is
turned on.
13. Anti-Carjack Mode. Enables Anti-Carjacking protection.
14. Horn Honk Output. Selects the output, when activated, to be pulsing or constant.
15. Aux 2 Auto Activate with Arm. When selected, the Auxiliary 2 output will activate when the system
is armed. This feature can be used to roll-up windows, close sunroofs, activate accessories, etc.
16. Auxiliary 1 Mode. Selects from momentary, 10 second timed, or latched operation for Auxiliary 1.
Momentary operation provides an output for as long as the transmitter button is pressed.
Timed operation provides an output that turns on for 10 seconds each time the transmitter button is
pressed. If the button is pressed again during the 30 seconds, the output will turn off.
Latched operation provides an output that turns on when the transmitter button is pressed and remains
on until the transmitter button is pressed again.
17. Auxiliary 2 Mode. Selects from momentary, 10 second timed, or latched operation for Auxiliary 2.
Momentary operation provides an output for as long as the transmitter button is pressed.
Timed operation provides an output that turns on for 10 seconds each time the transmitter button is
pressed. If the button is pressed again during the 30 seconds, the output will turn off.
Latched operation provides an output that turns on when the transmitter button is pressed and remains
on until the transmitter button is pressed again.
18. Ignition Armed Mode. When enabled, the security system may also be manually armed and disarmed
using the transmitter, while the ignition is on.
19. Extended Parking Lights. When selected, the parking lights will remain ON for 30 seconds after
disarming the system.
20. Warn-Away Pager Report. When Enabled, Warn-Away report will be sent to the pager. If Disabled
no Warn-Away report will be sent to the pager.
Page 28 - Astra 777-TC
21. Smart Siren Mode. When Enabled works with Optional ScyTek MP Player Siren Unit.
Branch Feature
1. Horn Chirps w/ Arm&Disarm Normal
2. Arm Mode
Button 1 (default)
Button 2
Horn Chirps
Passive Arming
Enabled
Off
Driver Only
Ignore
Enabled
Double
Silent
Enabled
3 seconds
Passive
Enabled
Continuous
Enabled
Timed
Timed
Enabled
Off
Button 3
Manual Arming
Disabled
On
All
Off
Disabled
Single
Normal
Disabled
1 second
Manual
Disabled
Flashing
Disabled
Pulsed
Pulsed
Disabled
On
3. Passive Door Locking
4. Ignition Controlled Locks
5. Ignition Controlled Unlock
6. Ignore Open Door Report
7. Auto Rearming
8. Door Unlock Pulse
9. Arming Chirps
10. Disarm with Aux 1
11. Door Lock Pulse Length
12. Anti-Carjack Type
13. Anti-Carjack Mode
14. Horn Honk Output
15. Aux 2 Activate on Arm
16. Aux 1 Mode
Set Override Code
Disabled
0.1 seconds
Full-time
Latched
Latched
17. Aux 2 Mode
18. Ignition Armed Mode
19. Extended Parking Lights
20. Warn-Away Pager Report
Enabled
Disabled
21. MP Player Siren Mode
Disabled
Enabled
Astra 777-TC - Page 29
Door Lock Diagrams
Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock
systems (separately unlocks driver and passenger doors) see following pages.
Negative Trigger
Positive Trigger
Reverse Polarity
Vacuum
Adding Actuators
Page 30 - Astra 777-TC
Two Stage Door Lock Diagrams
The Astra 777-TC is equipped with a dedicated Passenger Unlock output allowing Two Stage
Door Lock operation. When connected as shown below, disarming the system will unlock only
the driver’s door. Pressing the disarm button again will unlock all doors.
Two Stage Negative Trigger
Two Stage Positive Trigger
From Inverter or Relay
From Inverter or
Relay
Astra 777-TC - Page 31
Two Stage Door Lock Diagrams cont’d
Two Stage Reverse Polarity
Two Stage Adding Actuators
Page 32 - Astra 777-TC
Technical Information
FCC ID: OARRXAM2000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation
Call/Emergengy Override/Valet Switch
LED Light
Astra 777-TC - Page 33
Page 34 - Astra 777-TC
Astra 777-TC - Page 35
Wiring Diagram
Shock Sensor
Valet Switch
LED
Green
Red
Blue
(-) Lock output
not used
(-) Unlock output
Red
White
Brown
+12V
Parking light output (+) 7A
Siren output (+)
Blue/White Passenger Unlock output (-) 500mA
White/Red
Orange
Brown/White Horn output (-) 500mA
Black/White Dome Light output (-) 500mA
Blue
Gray
Yellow
Black
Violet
Green
Auxiliary 2 outout (-)
Armed output (-) 500mA
Hood/Trunk input (-)
Auxiliary 1 output (-) 500mA
Ignition +12V
Ground
Door Trigger input (+)
Door Trigger input (-)
Receiver Antenna
ScyTek Electronics
11627 Cantara Street
North Hollywood, CA 91605
© ScyTek Electronics 2008
Astra 777-TC 6-10-08
|